Blast machine forensics – my quest for IBC efficiency

By Gerhard Puttinger
Electrical Engineer at Wheelabrator

A blast machine is a complex beast. Assessing its energy consumption behaviour to find room for improvement therefore isn’t as straightforward as it sounds.

For my degree project in mechanical engineering, I made it my mission to systematically measure, evaluate and compare all the factors contributing to one machine’s energy consumption and efficiency. So, for several months in 2017, a Wheelabrator IBC-12/45-540-432, the trusted inclined belt conveyor concept, had my undivided attention. Every nook and cranny of it. Here’s what I did and what I found.

First, meet the subject

IBC Inclined Belt Conveyor Machine

In brief, the IBC range are continuous through-feed machines that treat workpieces individually. They are particularly suited to disc-shaped parts and are often used for blast-cleaning the disc-shaped part per se: the brake disc. It’s an efficient machine, designed for high-volume, high-quality production. I wanted to see if I could make it more efficient still.

The approach: no stone unturned

To get the complete, real picture of the machine’s energy consumption behaviour, I took into account every single motor and drive of the various components, assessed their individual input power, behaviour and energy conversion efficiency, and looked at alternative specifications and operating parameters for each.

IBC Inclined Belt Conveyor Machine

I measured the actual input power via a SIEMENS meter plugged in at the electric cabinet, taking readings every two seconds. All these data points were then fed into a specially adapted SPS software programme to analyse behaviour under varying operating conditions and calculate energy conversion coefficients.

When assessing energy conversion efficiency, it was important to really understand the role of each component in the operation of the machine. For example, drives on the abrasive recycling system show a very low energy conversion efficiency at normal fill levels, as they are deliberately over-engineered for normal operation. The simple reason: in the event of an unplanned machine stop, they have to be able to quickly restart an abrasive system with up to 200% the normal fill level.

Balancing acts

IBC Inclined Belt Conveyor MachineIn other areas, I’ve found some of the most important gains can be made by looking at the energy efficiency of stand-by versus switch-off – i.e., when is it more beneficial to do one rather than the other? I systematically looked at energy use for stand-by and start-up for each component, as well as the speed of restarting. Here again, it’s a balancing act, as the logical interplay of components has to be taken into account.

Start-up times in general are an interesting topic and I’ve found room for improvement in the better orchestration of start-ups of different machine elements. For example, it can be beneficial to start one component group gently and couple it with the start-up of another group. In the case of the IBC, I’ve found a slow-start of the abrasive system synched with the start-up of the blast wheels to achieve faster and more energy-efficient ramp-up. The optimum way of starting up the blast wheels is in pairs, timed with the abrasive system start-up. I was able to show that an improvement in start-up time from 88 to 46 seconds is possible, making temporary switch-offs worthwhile more often.

Other findings

IBC Inclined Belt Conveyor MachineIn addition to the optimisation of stand-by/switch-off and start-up phases, I’ve also found that it’s energetically more beneficial to run the machine at 75-100% capacity, using strategic switch-off of drives during periods of lower throughput. This means it is more efficient to run at high throughputs for a short period of time and then switch off until it is possible to run at high throughput again, rather than run continuously at low to medium throughput rates.

For the energy-efficient switch-off and restart of blast wheels during shorter periods of reduced throughput, I’ve examined and compared two options: soft starters and frequency converters. While the frequency converter option offered faster deceleration and start-ups of the wheels and allowed the restart of up to 6 wheels at once, it was four times as expensive as the soft starter. A switch-off with the latter option still enables a saving of 84% in stand-by energy, for a much lower initial investment.

The variability of workpieces is the biggest barrier to keeping the machine at 75-100% throughput, as the machine is specified for the workpiece that requires the maximum performance and will not be maxed out by other workpiece types, meaning it will run less efficiently.

Conclusion

There are many more observations and individual optimizations that I could talk about, but I wanted to simply give a flavour of the potential that can still be unlocked even in established machine concepts.

The systematic, holistic assessment of blast machine performance has shown that it is important to keep looking for optimisations in equipment, taking into account the specific practical and operational contexts the machine sits in, as well as the interplay of component groups.

The exercise has certainly taught me a lot about the importance of tailoring equipment to individual production requirements – and the key role it can play in achieving sustainable production.

If you have any questions on the project or my findings, please don’t hesitate to ask me in the comments.

Gerhard PuttingerThis post was written by
Gerhard Puttinger
Electrical Engineer at Wheelabrator
View biog

About WheelabratorBlog

Beneath the surface - expert opinion and insight on surface preparation from Wheelabrator.
This entry was posted in Technology, Wheelblast and tagged , , , . Bookmark the permalink.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s